Changing the Resolution of the Camera

Post Reply
eren
Posts: 14
Joined:Wed May 08, 2019 9:09 am

Changing the Resolution of the Camera

Postbyeren»

I'd like to change my current resolution (800x592) to 1600x1200. I have the camera which has the properties of:

6 mm 1600 × 1200 256 pixels 0.53 m 62° 10 fps


I was told to do the following:

* Disable Pixel Binning
* Reduce Trigger Frequency to 10 (As this supports the max. resolution I want to have, apparently).

* Re-Calibrate the Camera - OK!
* Possible increase the disparity range depending on the depth range to be covered - OK!


However, it would be nice to know where the first steps in the Webinterface are located.

That is, where can one disable pixel binning and reduce the trigger frequency? Under which tab? One has to do these steps for both of the cameras, I assume? Are these located under "Adv. Camera Settings"?

Thanks in advance.
Top
k.schauwecker
Posts: 72
Joined:Mon Mar 25, 2019 1:12 pm

Re: Changing the Resolution of the Camera

Postbyk.schauwecker»

The Pixel Binning configuration is found on the "Cameras" page. You should set binning horizontal and binning vertical both to 1 (you might have to change one after another). This configuration is set for both cameras.

Regards,
Konstantin
Top
eren
Posts: 14
Joined:Wed May 08, 2019 9:09 am

Re: Changing the Resolution of the Camera

Postbyeren»

I did that, and indeed the resolution is now shown as 1600x1200, however I do not get any image from any of the cameras, in the system status page I see the following:

Code:Select all

01:41:27守护进程。犯错watchdogd:过程ereod is not running! Starting! 01:41:27 daemon.info stereod: Daemon started 01:41:27 daemon.info stereod: Using cameras 22857460; 22844036 01:41:28 daemon.warn stereod: Unable to write camera feature: Value = 1600 must be equal or smaller than Max = 800. : OutOfRangeException thrown in node 'Width' while calling 'Width.SetValue()' (file 'IntegerT.h', line 79) 01:41:28 daemon.warn stereod: Unable to write camera feature: Value = 1200 must be equal or smaller than Max = 600. : OutOfRangeException thrown in node 'Height' while calling 'Height.SetValue()' (file 'IntegerT.h', line 79) 01:41:28 daemon.info stereod: Resetting FPGA 01:41:28 daemon.warn stereod: Could not load rectification map: Rectification map size mismatch!
I wanted to calibrate but that page also shows no image. I think something went wrong.
Top
k.schauwecker
Posts: 72
Joined:Mon Mar 25, 2019 1:12 pm

Re: Changing the Resolution of the Camera

Postbyk.schauwecker»

This seems odd. Can you please email your configuration (can be downloaded from the maintenance page) to service@www.samlea.com. Also please check that on the status page it says "Model: SceneScan Pro"
Top
eren
Posts: 14
Joined:Wed May 08, 2019 9:09 am

Re: Changing the Resolution of the Camera

Postbyeren»

Sent, and yes, it does say "Model: SceneScan Pro".
Top
k.schauwecker
Posts: 72
Joined:Mon Mar 25, 2019 1:12 pm

Re: Changing the Resolution of the Camera

Postbyk.schauwecker»

I received the file. I'm checking the configuration and will get back to you.
Top
eren
Posts: 14
Joined:Wed May 08, 2019 9:09 am

Re: Changing the Resolution of the Camera

Postbyeren»

It was the outdated firmware problem, after the patching the error is gone.
Top
Post Reply